Pengembangan Metode Pengujian Kuat Tekan dan Modulus Elastisitas Pada Campuran Aspal

Edi Yusuf Adiman, Tommy Iduwin, Arief Setiawan

Abstract


This research is a development of testing methods for compressive strength and elastic modulus in asphalt mixture. The test used is the Unconfined Compressive Strength (UCS) method. The test specimens shall be cylinders 3.0 inches in diameter and 6.0 inches in height. The asphalt mixture used is the AC-WC. The asphalt content was obtained based on the optimum asphalt content, which was 5.56%. The test results showed that the compressive strength of the AC-WC ranges 5.81 MPa - 6.26 MPa, and then the elastic modulus ranges 899 MPa - 1,295 MPa. For good test results, it is necessary to pay attention to the temperature test and the flatness of the specimen’s surface.

Keywords


asphalt mixture, compressive strength, elastic modulus, AC-WC.

References


Amrin, M. A., Gaus, A., & Darwis, M. (2017). Studi Kuat Tarik Tidak Langsung Pada Campuran Asphalt Concrete Menggunakan Asbuton. Jurnal Sipil Sains, 7(14), 1–12.

ASTM-C39. (2018). Standard Test Method for Compressive Strength of Cylindrical Concrete Specimens. American Society for Testing and Materials.

ASTM-D1074. (1996). Standard Test Method for Compressive Strength of Asphalt Mixtures. American Society for Testing and Materials.

ASTM-D2166. (2000). Standard Test Method for Unconfined Compressive Strength of Cohesive Soil. American Society for Testing and Materials.

Badaron, S. F., Gecong, A., Anies, M. K., Achmad, W. M., & Setiani, E. P. (2019). Studi Perbandingan Kuat Tarik Tidak Langsung terhadap Campuran Aspal Beton dengan menggunakan Limbah Marmer dan Abu Sekam Padi sebagai Filler. PENA TEKNIK: Jurnal Ilmiah Ilmu-Ilmu Teknik, 4(2), 145. https://doi.org/10.51557/pt_jiit.v4i2.593

Chairuddin, F., Wihardi Tjaronge, M., Ramli, M., & Patanduk, J. (2016). Compressive Strength of Permeable Asphalt Pavement Using Domato Stone (Quarzite Dolomite) and Buton Natural Asphalt (BNA) Blend. International Journal of Engineering and Technology, 8(3), 183–186. https://doi.org/10.7763/ijet.2016.v8.881

Dirjen Bina Marga. (2020). SPESIFIKASI UMUM 2018 UNTUK PEKERJAAN KONSTRUKSI JALAN DAN JEMBATAN (REVISI 2). KEMENTERIAN PEKERJAAN UMUM DAN PERUMAHAN RAKYAT.

Dowling, N. E. (2013). Mechanical behavior of materials: engineering methods for deformation, fracture, and fatigue (4th ed.). Pearson.

S. STARODUBSKY, I. BLECHMAN, M. L. (1994). Stress-strain relationship for asphalt concrete in compression. Materials and Structures, 27, 474–482.

Saifuddin, I. B., Gaus, A., & Anwar, C. (2017). Studi Karakteristik Kuat Tekan Pada Campuran Asphalt Concrete. Jurnal Sipil Sains, 07, 25–34.

SNI 03-6758. (2002). Metode pengujian kuat tekan campuran beraspal. Pustran Balitbang PU.

SNI 06-2489. (1991). METODE PENGUJIAN CAMPURAN ASPAL DENGAN ALAT MARSHALL (Issue 1). Pustran Balitbang PU.

SNI 1974. (2011). Cara Uji Kuat Tekan Beton dengan Benda Uji Silinder. Badan Standardisasi Nasional.

SNI 3638. (2012). SNI 3638: Metode Uji Kuat Tekan-Bebas Tanah Kohesif. Badan Standardisasi Nasional.




DOI: https://doi.org/10.30601/jtsu.v7i2.2040

Refbacks



Copyright (c) 2021 Edi Yusuf Adiman

Creative Commons License
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.

Jurnal Teknik Sipil Unaya


Creative Commons License
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.

© Jurnal Teknik Sipil Unaya : Published by Center for Research and Community Service (LPPM) University of Abulyatama, Aceh, Indonesia. 2019